International Perfection Undercoat A+B Bianco YRA0003 0,75Lt N702458COL6662

PRODUCT DESCRIPTION
High performance two part polyurethane undercoat suitable for all finishes. Perfection Undercoat is the ideal base for a long lasting scheme, when used with Perfection Finish.

* Easy application, fast drying and easy sanding

* Excellent gloss hold out of finish coats

* Semi-gloss appearance

PRODUCT INFORMATION
Colour YRA003-White, YRA302-Blue
Finish Semi-gloss
Specific Gravity 1.39
Volume Solids 50%
Mix Ratio 3:1 by volume (as supplied)
Converter/Curing Agent YGA006
Typical Shelf Life 2 yrs
VOC (As Supplied) 488 g/lt
Unit Size 750 ml

DRYING/OVERCOATING INFORMATION
Drying
5°C (41°F)  15°C (59°F)  23°C (73°F)  35°C (95°F)
Touch Dry 11 hrs 7 hrs 3 hrs 2 hrs
Sandable 48 hrs 30 hrs 16 hrs 12 hrs
Pot Life 5 hrs 3 hrs 2 hrs 1 hrs Overcoating
Substrate Temperature
5°C (41°F)  15°C (59°F)  23°C (73°F)  35°C (95°F)
Overcoated By Min Max Min Max Min Max Min Max
Interdeck 32 hrs 4 days 16 hrs 3 days 10 hrs 2 days 8 hrs 1 days
Perfection 32 hrs 4 days 16 hrs 3 days 10 hrs 2 days 8 hrs 1 days
Perfection Undercoat 32 hrs 4 days 16 hrs 3 days 10 hrs 2 days 8 hrs 1 days
Toplac 32 hrs 4 days 16 hrs 3 days 10 hrs 2 days 8 hrs 1 days

APPLICATION AND USE
Preparation: PREVIOUSLY PAINTED SURFACES
In Good Condition Wash down with Super Cleaner, rinse with fresh water and allow to dry. Abrade with 280-320 grade (grit) paper.
In Poor Condition: Remove all previous coatings and prime the substrate.
PRIMING All preparation for bare substrates is covered on the appropriate primer datasheet.
BARE WOOD Prime with Interprotect.
STEEL Prime with Interprotect.
ALUMINIUM Prime with Interprotect.
GRP Wash down with Super Cleaner, rinse with fresh water and allow to dry. Abrade with 180-220 grade paper.
AGED/WEATHERED GELCOATS Degrease with solvent or suitable detergent cleaner. Sand well using 180-220 grade paper. Clean thoroughly and allow to dry completely. To avoid potential pinholing, apply 3 coats of an International 2 pack epoxy primer which must be then overcoated with an International 2 pack undercoat prior to topcoat application.
ALL SUBSTRATES If any filling is required use the appropriate product from the International range.
Method If maximum overcoating time of previous coating/primer is exceeded, abrade using 180-220 grade paper. Remove dust with a dust wipe. Apply 1-2 coats.

TIPS: Mixing Stir contents of each part prior to mixing. Add Curing Agent to the Base, stir and leave for 10 minutes to allow bubbles to disperse.
Thinner Thinner No.9
Cleaner Thinner No.9
Ventilation and Humidity Control Apply in dry, well ventilated conditions. Avoid excessively humid conditions, over 80% relative humidity.
Spray application - PROFESSIONAL USE ONLY.

Other: Best applied at 15°C. To give extra depth of colour, Perfection finish colours may be added to Perfection Undercoat. Both products should be mixed with respective curing agent first.
Some Important Points Do not use unless mixed thoroughly with the curing agent at specified ratio. Product temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Ambient temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Substrate temperature should be minimum 5°C/41°F and maximum 35°C/95°F.
Compatibility/Substrates Will crack on carvel and clinker/lapstrake hulls. Perfection Undercoat should be applied over cured epoxy primers or fillers or onto cured GRP/Composite. It should not be used over any one pack products.
Number of Coats 1-2
Coverage (Theoretical) - 13.16 m²/lt
(Practical) - 11.8 m²/lt
Recommended DFT per coat 38 microns dry by brush
Recommended WFT per coat 76 microns wet by brush
Application Methods Brush, Roller, DO NOT SPRAY - Professional applicators looking for details on spray application should refer to the Perfection Undercoat (Professional) datasheet

TRANSPORTATION, STORAGE AND SAFETY INFORMATION
Storage GENERAL INFORMATION:
Exposure to air and extremes of temperature should be avoided. For the full shelf life of Perfection Undercoat to be realised ensure that between use the container is firmly closed and the temperature is between 5°C/41°F and 35°C/95°F.
Keep out of direct sunlight.

TRANSPORTATION:
Perfection Undercoat should be kept in securely closed containers during transport and storage.

Safety GENERAL:
Contains isocyanates which may be harmful to the respiratory tract. Read the label safety section for Health and Safety Information, also available from our Technical Help Line.

DISPOSAL:
Do not discard tins or pour paint into water courses, use the facilities provided. It is best to allow paints to harden before disposal.
Remainders of Perfection Undercoat cannot be disposed of through the municipal waste route or dumped without permit.
Disposal of remainders must be arranged for in consultation with the authorities.

IMPORTANT NOTES The information given in this sheet is not intended to be exhaustive. Any person using the product without first making further written enquiries as to the suitability of the product for the intended purpose does so at their own risk.

Unit size 0.75lt.