International Ultra 300 Antifouling 2.5Lt Blue-Blau-Bleu Hard matrix 458COL643

International Antifouling Ultra 300 2.5Lt Blue-Blau-Bleu

Offers protection in the highest fouling conditions where a hard, scrubbable antifouling is required. Ideal for fast powerboats.
* High strength, hard antifouling
* Hard, scrubbable finish to allow cleaing if needed
* Suitable for sanding to provide a smooth finish
* Smooth finish for maximum glide through the water
* Contains Biolux® technology for sustained antifouling protection

PRODUCT INFORMATION
Colour YBA303-Dover White, YBA323-Green , YBA331-Light Blue, YBA333-Blue, YBA341-Red , YBA353-Navy, YBA363-
Grey, YBA366-Princess Grey, YBA393-Black Please check availability of full colour range. Not all colours are available in every country.
Finish: Matt
Specific Gravity 1.5
Volume Solids 45% average
Typical Shelf Life: 2 yrs
VOC (As Supplied) 485 g/lt
Unit Size: 750 ml 2.5 Lt

DRYING/OVERCOATING INFORMATION
5°C (41°F)  15°C (59°F)  23°C (73°F)  35°C (95°F) 
Touch Dry 1 hrs 45 mins 30 mins 20 mins
Immersion 24 hrs 12 hrs 8 hrs 6 hrs
Note: Max. Immersion Times are as follows: 5-15°C - 3 mths; 23°C - 2 mths; 35°C - 1 mth Overcoating
Substrate Temperature
5°C (41°F)  15°C (59°F)  23°C (73°F)  35°C (95°F) 
Overcoated By Min Max Min Max Min Max Min Max
Interspeed Ultra 16 hrs ext 10 hrs ext 6 hrs ext 4 hrs ext
Micron 66 16 hrs ext 10 hrs ext 6 hrs ext 4 hrs ext
Micron Extra (Professional) 16 hrs ext 10 hrs ext 6 hrs ext 4 hrs ext

APPLICATION AND USE
Preparation: PREVIOUSLY ANTIFOULED SURFACE
In Good Condition: Rinse with freshwater and allow to dry. If old antifouling is incompatible or unknown, seal with Primocon.
In Poor Condition: Use Interstrip to remove all traces of antifouling.

PRIMING
Preparation tips for bare/natural substrates are set out in the relative primer datasheet.
NATURAL GRP: Gelshield 200 for osmosis protection, or Primocon.
STEEL/IRON: Prime with Interprotect or Primocon.
LEAD: Prime with Interprotect or Primocon.
WOOD: Prime with Interprotect or Primocon.
Method: Apply two coats per season.
Useful tips: Mixing: Stir well before use.
Thinner YTA085 Thinners No.3
Thinning is not recommended.
Cleaner YTA085 Thinners No.3
Other: True colour will develop after immersion. It is important to apply the product quantity calculated on the basis of the spreading rate, and if necessary with an extra coat.  It is also important to respect the thicknesses as advised to obtain the best results. To prevent poor result and performance, ensure the correct amount of paint is applied using the coverage as a guide (see spreading rate). The temperature of the product should be between a minimum of  5°C/41°F and a maximum of 35°C/95°F.  The ambient temperature should be between a minimum of 5°C/41°F and a maximum of  35°C/95°F. The surface temperature should be a minimum of 1°C above dew point and a maximum of 35°C.


Compatibility/Substrates
GRP, wood, steel/iron, lead. Not suitable for use over aluminium/alloy substrates or zinc plated surfaces. Can be applied directly over most types of antifoulings, provided they are in sound condition
Number of Coats: 2-3 by brush/roller
Coverage/spreading rate (Theoretical) - 10.5 m²/lt by brush
(Practical) - 9.4 m²/lt by brush
Recommended dry film thickness per coat: 43 microns
Recommended wet film thickness per coat: 96 microns

Application Method
Brush, Roller, AIRLESS SPRAY NOT RECOMMENDED
Pack 2,5 lt.
Color: Blue-Blau-Bleu.