Veneziani Eurosprint Pro Antifouling White 5 Lt 473COL259

Veneziani Eurosprint Pro Antifouling White 5 Lt

High quality, hard matrix, antifouling suitable for every type of seas, lakes or mixed waters. Good resistance to abrasion, applicable on sailing vessels and motor ships even if they exceed 35 knots.
Applicable on wooden, iron and fiberglass hulls.
It complies with the IMO (AFS/CONF/26) antifouling requirements and it is certified by Rina and Lloyd’s Register boards. Furthermore, it contains active substances according to the BPR Regulation (Regulation (EU) No 528/2012).
Only white color is suitable for alloy hulls.

Product information
Finish Matt
Colour White .153
Solids (by volume) ASTM D2369  46 ± 2 % (white)
Specific gravity UNI EN ISO 2811-1  1,60 ÷ 1,70 g/cm³ (white)
Flash point UNI EN ISO 13736   34° C
Average shelf life 3 years
VOC (calculated average content) ISO 11890-2/2006    360 g/l

SURFACE PREPARATION
Surfaces with old antifouling
Good condition: remove contaminants and any vegetation through high pressure wash with fresh water.
Sand down with 120-180 grain paper. If the old antifouling is unknown or of a different nature apply a coat
of an insulator like TICOPRENE.

Bad conditions: remove contaminants, possibly vegetation and non-adherent material through high
pressure wash with fresh water. Sanding with 80-120 grain paper or with a slight sandblasting, paying
attention not to damage the paint system underneath the old antifouling. Apply coat of ADHERPOX or
TICOPRENE primer onto the entire treated area before proceeding with the antifouling

New surfaces or brought to new
Fiberglass: Degrease the surface to be treated with solvent or with a suitable detergent. Wash with fresh water and remove any traces of oil and grease. All surfaces to be painted must be clean, dry and free of contaminants. Sandpaper with abrasive paper no. P180 - P220 and apply the primer onto the treated surface. Before proceeding with the application of the products, blow with clean and dry air to remove any
residual sanding and dirt.
Steel: Wash with fresh water and remove any traces of oil and grease (in case washing with the specific solvent). All surfaces to be painted must be clean, dry and free of contaminants. Perform a sandblasting treatment of grade Sa 2½ or, after consultation with our technicians, mechanical cleaning degree St 3.
Overcoat with the proper primer the treated metal before oxidizing principles are present.
Before proceeding with the application of the products, blow with clean and dry air to remove any residual sanding and dirt.

New wood: The moisture content of the support must not exceed 18%. All surfaces to be painted must be clean, dry and free of contaminants. Sandpaper with paper no. P80 - P120. Before proceeding with the application of the products, blow with clean and dry air to remove any residual sanding and dirt.
Lead: Wash with fresh water and remove any traces of oil and grease (in case washing with the specific solvent). All surfaces to be painted must be clean, dry and free of contaminants. Waxing with large grain disks (mechanical cleaning) the surface layer of metal must be completely and uniformly renewed,
removing any oxidation residue and coated with the primer provided on the same day of preparation. Be careful not to exceed the incision. Before proceeding with the application of the products, blow with clean and dry air to remove any residual sanding and dirt.

CONDITIONS DURING THE APPLICATION
In order to avoid the formation of condensation, the temperature of the surface should be at least 3 °C above dew point. During the application and curing the min. ambient temperature must not be lower than 10 °C or higher than 30 °C; substrate temperature must not be lower than 5 °C, since curing is remarkably reduced at lower temperatures.
Application is not advisable when relative humidity exceeds 80%. The term-hygrometric survey should be carried out near the surface to be coated. Make sure there is enough ventilation when the application takes place in closed areas

Recommended thinner: 6470, our code 473COL253.
Unit size 5 lt.
Colour: White 153