Veneziani Raffaello Next Deep Blue .512 750ml Antifouling N709473COL384

Veneziani Raffaello Next Deep Blue .512 750ml Antifouling

Superior antifouling paint with hydrophilic matrix. Due to the high copper content and the presence of pure carbon particles, a good antifouling power and natural flowability are guaranteed in all operating conditions. Effective in warm, temperate seas and mixed waters. It has a controlled solubility and it can therefore be conveniently used on both medium-speed hulls and sailboats. It does not accumulate excessive thickness over time, consuming progressively during exercise.
It complies with the IMO (AFS/CONF/26) antifouling requirements and contains active substances according to the BPR Regulation (Regulation (EU) No 528/2012).
Only white color is suitable for light alloy hulls.

Product information
Aspect Matt.
Colour Deep Blue .512
The colour of the antifouling paint after diving may be slightly different. Small tinting differences may occur between different production batches: in case mix them before the application.
Solids (by volume) 50 ± 2 %.
Specific gravity 1,90 ÷ 2,00 g/cm³.
Flash point 30 °C.
Shelf life 3 years.
VOC (calculated avarage content) 417 g/l.

SURFACE PREPARATION
• Surfaces with old antifouling
Good condition: remove contaminants and any vegetation through high pressure wash with fresh water.
Sanding with 120-180 grain paper. If the old antifouling is unknown or of a different nature apply a coat of an insulator like Ticoprene AL.
Bad conditions: remove contaminants, possibly vegetation and non-adherent material through high pressure wash with fresh water. Sanding with 80-120 grain paper or with a slight sandblasting, paying attention not to damage the paint system underneath the old antifouling. Apply coat of ADHERPOX or TICOPRENE AL primer onto the entire treated area before proceeding with the antifouling application.
• New surfaces or brought to new
Fiberglass: Degrease the surface to be treated with solvent or with a suitable detergent. Wash with fresh water and remove any traces of oil and grease. All surfaces to be painted must be clean, dry and free of contaminants. Sandpaper with abrasive paper no. P180 - P220 and apply the primer onto the treated surface. Before proceeding with the application of the products, blow with clean and dry air to remove any residual sanding and dirt.
Steel: Wash with fresh water and remove any traces of oil and grease (in case washing with the specific solvent). All surfaces to be painted must be clean, dry and free of contaminants. Perform a sandblasting treatment of grade Sa 2½ or, after consultation with our technicians, mechanical cleaning degree St 3.
Overcoat  with  the  proper  primer  the  treated  metal  before  oxidizing  principles  are  present.
Before proceeding with the application of the products, blow with clean and dry air to remove any residual sanding and dirt.
Lead: Wash with fresh water and remove any traces of oil and grease (in case washing with the specific solvent). All surfaces to be painted must be clean, dry and free of contaminants. Waxing with large grain disks (mechanical cleaning) the surface layer of metal must be completely and uniformly renewed, removing any oxidation residue and coated with the primer provided on the same day of preparation. Be careful not to exceed the incision. Before proceeding with the application of the products, blow with clean and dry air to remove any residual sanding and dirt.
New wood: The moisture content of the support must not exceed 18%. All surfaces to be painted must be clean, dry and free of contaminants. Sandpaper with paper no. P80 - P120. Before proceeding with the application of the products, blow with clean and dry air to remove any residual sanding and dirt.

APPLICATION DATA
Thinner/Cleaning tools: 6470
Dry film thickness:
- Standard application range: 40 - 60 μm
- Recommended 40 μm
Wet film thickness:
- Standard application range: 80 - 120 μm
- Recommended 80 μm
Theoretical coverage at the recommended thickness m2/liter: Application range at the recommended thickness - 10.
N° coats 2: coats for a seasonal protection. Apply an extra coat in areas subjected to higher consumption/friction.
Recommended primers: ADHERPOX suitable for all substrates, TICOPRENE AL usable as primer on wood, iron, fiberglass or as  insulator on old antifouling paints (Adherglass, Unikote PRO).

Unit size 0.75 Lt.
Deep Blue .512 colour.